x
Part No: CAA-00267
Region: americas apac
Molex PowerCat 6 (C6) 4 Pair UTP cable has been designed to support high-speed data transmission systems. The cable is part of the PowerCat 6 range of products that are designed to comply with the Category 6 specification.
We recommend that the full range of PowerCat 6 products are used in a system to maximize cabling performance, providing extended frequency response and enhanced bandwidth.
Test results from Intertek are available here for CAA-00267
MECHANICAL
Conductor Size : 23 AWG Solid Bare Copper Wire
Primary Insulation : Solid Polyethylene
Nominal O.D.: 1.045 + 0.02mm
Twinning: Right hand lay
Sheath Type: LS0H 332.1
Minimal Wall: 0.55mm
Nominal O.D: 6.1mm
Cable weight: 13.6 Kgs Nominal
NVP: 67%
Bending Radius: <4 X Cable Diameter (mm) at -20°C ± 1°C
Pulling Force:
Short Term: 400N
Long Term:110N
Temperature Range:
Installation: 0°C to +50°C
Operation: -20°C to +70°C
ELECTRICAL
Characteristic Impedance: 100±15Ω
Conductor Resistance: ≤9.38Ω/100m
Mutual Capacitance: <5.6nF/100m
Resistance Unbalance: 5% Max
Capacitance Unbalance: 330pF/100m
Delay Skew: <45nS
COMMERCIAL STANDARDS
EN 50173 2nd Edition, ISO/IEC 11801
2nd Edition, EIA / TIA 568.2-D
IEC 60754-2, IEC 61034-2
Fire Propagation Test: UL 1581
VW1, IEC 60332.1, EN0256-2-1
Performance Characters - Category 6 EIA / TIA 568.2-D
Support IEEE 802.3 1000Base-T Zero BER
INSTANT VOLT rated 300V
Oxygen index: > 29% (ASTM D 2863)
Temperature index: 250 degC. (ASTM D 2863)
Acid Gas generation: max 0.5% by weight (BS EN 50267-2-1)
RoHS Compliant
PoE
Our PowerCat 6 system is suitable for PoE applications as defined below:
- IEEE 802.3bt from Type 1 to Type 4, and CISCO UPoE+
- IEEE 802.3bt Type 1 up to 15.4W (350mA per pair / 2 pairs energized)
- IEEE 802.3bt Type 2 up to 30W (600mA per pair / 2 pairs energized)
- IEEE 802.3bt Type 3 up to 60W and CISCO UPoE (600mA per pair / 4 pairs energized)
- IEEE 802.3bt Type 4 up to 90W and CISCO UPoE+ (1000mA per pair / 4 pairs energized)
Notes:
- For new installations of PoE Type 3 / Class 5 and above that wish to be eligible for the Molex 25 year Application Assurance Warranty, we require Category 6A cable to be used throughout. To confirm your PoE / RP3 cabling design is eligible for the Molex 25 year Application Assurance Warranty, your design must be verified and validated with the Molex PoE Calculator. Read more at https://www.molexces.com/poe-calculator
- Molex recommends that the PoE feature on an individual switch port is power disabled prior to unplugging the associated powered Device.
- Molex recommends that the full range of PowerCat 6 products be used in a system to maximize cabling and PoE performance. Details on Molex requirements for Warranty can be found at: https://www.molexces.com/about-us/ourwarranty/
